Dynomax Ride In / Ride Out
All in One Motorcycle Performance Preparation Service

In conjunction with The Cylinder Head Shop, Dynomax is able to offer a Ride In / Ride Out Motorcycle Preparation Service. The specification of the engine tuning is entirely your choice. Dynomax will dyno test your bike before any work commences, then remove the engine, dismantle and take the cylinder head to The Cylinder Head Shop for its attention.

Meanwhile, Dynomax will prepare the rest of the engine to your chosen specification ( i.e. balance crankshaft, con-rods and pistons; measure crankshaft bearings, piston rings, clutch plates, etc. - and replace parts as required).

When the cylinder head is complete and returned to Dynomax, the engine is rebuilt, squish set and camshafts dialed in.

Finally, when installed into the motorcycle, the engine is dyno tested again and the air / fuel ration optimised to give the maximum performance.

Click here for Map and Directions to Dynomax.

" No matter if it is for a World SuperBike engine, or for a street-legal system, developing an exhaust system is a methodical, painstaking process of performing many tests, each of which may only give a small improvement, but leading to superior end results. What I need, therefore, is a tool that can measure each development step I make with absolute accuracy and consistency, and in the quickest possible way. For me ... the Dynojet Dyno is that tool. "

Igor Akrapovic, Akrapovic Exhaust System Technology

Akrapovic is the supplier of choice for Kawasaki, Yamaha, and Suzuki World SuperBike Factory Race Teams.

Typical graph showing power and torque curves before
and after exhaust and fuelling modifications.


Specialist services for any motorcyle
performance related work.


Dyno Testing
Carb / Fuel Injection Setup
Engine Preparation
Race tuning
Suspension Upgrades
Research and development undertaken
Commissioned contract work accepted
Confidentiality guaranteed


No more bullshit, we have the facts ...

So how does a Dynojet dynobench work?




A dynamometer is an instrument for measuring force exerted by motor vehicles. A machine that's used to measure the horsepower output of an engine. A " chassis dyno " has a large roller upon which the drive wheel of the motorcycle is placed. The vehicle is run up to a certain speed and put under load so the amount of power that's being delivered to the rear wheel can be measured accurately.

A dyno can also be used to simulate actual riding or racing conditions when troubleshooting various drivability problems or checking for successful engine development. Dynos are also used to simulate driving conditions during certain types of noise and emissions tests.

Through the use of state-of-the-art computer technology, Dynojet's Model 200 Dynamometer allows you to quickly and accurately diagnose performance problems. By simulating the best "seat-of-the-pants" road testing right in the shop, problems are easily diagnosed in a fraction of the time. Shop sales, service work, and credibility all benefit with a Dynojet Chassis Dynamometer.

The Model 200 Dynamometer includes:
  • Inertia Dynamometer Chassis with standard wheel base up to 84 inches
  • Measures up to 500 horsepower
  • Dynoware EX+ hardware includes:
    CPU Module: Com Port Interface, runs on 12VDC for offsite use & 240VAC
    Dyno Module: Sends and receives data to and from the Dyno
    Atmosperic Sensing Module: Automatically measures absolute pressure, air temperature and relative humidity
    RPM Module: Receives and processes ignition spark signals for correct engine speed measurement
  • Primary Wire Inductive tachometer pickup
  • Secondary Inductive Pickups [ spark plug clamps connect directly to spark plug wires ]
  • WinPEP Software, Windows 95 to Windows 2000
  • Bike Starter System [ uses external battery ]
  • Wheel Lock for safe handling of customers motorcycles

Dynomax's fully mobile Dynojet Model 200 dyno is available for hire at private or corporate events. Ring for details and ask for Linsey.

Dynomax UK Ltd
Unit A Holmes Court
Boston Road Industrial Estate
Horncastle Lincolnshire LN9 6JW
Tel: 01507 522292 Fax: 01507 524668
Mob: 07799 318709

For more details, please see the company's website : http://www.dynomaxuk.com/

back                HOME
forward

Contact details:

Cylinder Head Shop
Nucleus Works
1a, Coopers Place
Combe Lane
Wormley
Surrey
GU8 5SZ
T : 01428 685883 (INT 0044 1428 685883)
M : 07810273600 (INT 0044 7810273600)
For specific requests, please send us your inquiries to;
E:len@cylinderheadshop.co.uk

Cylinder Head Shop is the business name for tuningforspeed.com ltd.
Director:
T. L. Paterson